Product ITEM is unavailable. See products from the same category below.
Pipe & Conduit Thread Taps
Pipe and conduit thread taps come in thread standards and sizes that are used on parts in pipe and conduit systems because they allow mated parts to form a pressure-tight seal. These taps create or repair internal threads in pipe, conduit, and fittings so they can mate with parts that have matching external threads. They are turned with a tap wrench for manual tapping applications or installed into a toolholder on a machine for machine tapping applications.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot.
This 5319S pipe tap is made of high speed steel and has a 0.438 inch diameter, 1⅜ inch long shank. It is designed for use with steel, and meets the standards for USCTI Table 311, USCTI. This 5319 series pipe tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has five flutes.
This 5319S pipe tap is made of high speed steel and has a 0.438 inch diameter, 1⅜ inch long shank. It is designed for use with steel, and meets the standards for USCTI Table 311, USCTI. This 5319 series pipe tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has five flutes.
This 5319 pipe tap is made of high speed steel and has a 0.906 inch diameter, 1⅞ inch long shank. It is designed for use with aluminum, brass, bronze, copper, and meets ANSI and USCTI standards. This 5319 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3¼ inch length. Plus it has five flutes.
This 5319 pipe tap is made of high speed steel and has a 0.906 inch diameter, 1⅞ inch long shank. It is designed for use with aluminum, brass, bronze, copper, and meets ANSI and USCTI standards. This 5319 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3¼ inch length. Plus it has five flutes.
This 5323 pipe tap is made of high speed steel and has a 0.700 inch diameter, 1½ inch long shank. It is for use with steel, and meets the standards for USCTI and American National Standard straight Pipe, USCTI. This 5323 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2 9/16 inch length, plus it has four flutes.
This 5323 pipe tap is made of high speed steel and has a 0.700 inch diameter, 1½ inch long shank. It is for use with steel, and meets the standards for USCTI and American National Standard straight Pipe, USCTI. This 5323 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2 9/16 inch length, plus it has four flutes.
This 5329PTF pipe tap is made of high speed steel and has a 0.312 inch diameter shank. It is for use with aluminum, brass, bronze, copper, hardened steel, steel, and meets the standards for USCTI and American Standard Dryseal Pipe Form, ANSI. This 5329PTF series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5329PTF pipe tap is made of high speed steel and has a 0.312 inch diameter shank. It is for use with aluminum, brass, bronze, copper, hardened steel, steel, and meets the standards for USCTI and American Standard Dryseal Pipe Form, ANSI. This 5329PTF series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5323 pipe tap is made of high speed steel and has a 0.312 inch diameter, 1⅜ inch long shank. It is for use with steel, and meets the standards for USCTI and American National Standard straight Pipe, USCTI. This 5323 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5323 pipe tap is made of high speed steel and has a 0.312 inch diameter, 1⅜ inch long shank. It is for use with steel, and meets the standards for USCTI and American National Standard straight Pipe, USCTI. This 5323 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5320 pipe tap is made of vanadium high speed steel and has a 0.438 inch diameter, 1⅜ inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI and USCTI standards. This 2320/5320 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5320 pipe tap is made of vanadium high speed steel and has a 0.438 inch diameter, 1⅜ inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI and USCTI standards. This 2320/5320 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5329PTF pipe tap is made of high speed steel and has a 0.700 inch diameter shank. It is for use with aluminum, brass, bronze, copper, hardened steel, steel, and meets the standards for USCTI and American Standard Dryseal Pipe Form and USCTI. This 5329PTF series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction with a 2½ inch length, plus it has four flutes.
This 5329PTF pipe tap is made of high speed steel and has a 0.700 inch diameter shank. It is for use with aluminum, brass, bronze, copper, hardened steel, steel, and meets the standards for USCTI and American Standard Dryseal Pipe Form and USCTI. This 5329PTF series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction with a 2½ inch length, plus it has four flutes.
This 5320 pipe tap is made of vanadium high speed steel and has a 0.313 inch diameter, 1⅜ inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI and USCTI standards. This 2320/5320 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length, plus it has four flutes.
This 5320 pipe tap is made of vanadium high speed steel and has a 0.313 inch diameter, 1⅜ inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI and USCTI standards. This 2320/5320 series pipe tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length, plus it has four flutes.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot. Note: large shank supplied unless other wise specified, 0.4375 inches diameter.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot. Note: large shank supplied unless other wise specified, 0.4375 inches diameter.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot.
NPT high speed maintenance taper pipe tap is for use by hand or for tapping under power. American Standard Pipe Tap thread form having a taper of 3/4 inch per foot.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
