Threading

This hand tap is made of carbon steel and has a 0.255 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1183 series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has four flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.255 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1183 series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has four flutes and a straight shank.

Maintenance taps are ground thread taps made from high speed steel. For use by hand or for tapping under power. Chamfer-taper. (7-10 pitches)

Maintenance taps are ground thread taps made from high speed steel. For use by hand or for tapping under power. Chamfer-taper. (7-10 pitches)

This hand tap is made of carbon steel and has a 0.168 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1125 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has three flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.168 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1125 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has three flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.194 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1142 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has three flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.194 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1142 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has three flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.141 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1112 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has three flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.141 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1112 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has three flutes and a straight shank.

Combination drill taps, complete hole drilling & tapping in one operation with power drill saves labor & time. Made from high-speed steel vs. carbon steel for longer life. High quality hex shank ensures strong connection to drill chuck.

Combination drill taps, complete hole drilling & tapping in one operation with power drill saves labor & time. Made from high-speed steel vs. carbon steel for longer life. High quality hex shank ensures strong connection to drill chuck.

This hand tap is made of carbon steel and has a 0.194 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1152 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has three flutes and a straight shank.

This hand tap is made of carbon steel and has a 0.194 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 312-1152 series hand tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has three flutes and a straight shank.

This M2 hand tap is made of high speed steel and has a 0.255 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 440-1118 series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has four flutes and a straight shank.

This M2 hand tap is made of high speed steel and has a 0.255 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 440-1118 series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has four flutes and a straight shank.

This bottoming hand tap is 66 millimetres long, with a M6.0 x 1.00 thread and a 6.3-millimetre shank diameter. This hand tap is made from high speed steel.

This bottoming hand tap is 66 millimetres long, with a M6.0 x 1.00 thread and a 6.3-millimetre shank diameter. This hand tap is made from high speed steel.

This M2 hand tap is made of high speed steel and has a 0.381 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 440-1190 series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has four flutes and a straight shank.

This M2 hand tap is made of high speed steel and has a 0.381 inch diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 440-1190 series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has four flutes and a straight shank.

This tap and die set is made of carbon steel. It includes 2 straight tap wrenches, t-handle tap wrench, die stocks, a plastic case, and is designed for use with ferrous metal, and meets the standards for ANSI. This tap and die set has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction.

This tap and die set is made of carbon steel. It includes 2 straight tap wrenches, t-handle tap wrench, die stocks, a plastic case, and is designed for use with ferrous metal, and meets the standards for ANSI. This tap and die set has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction.

This SST high performance power tap is 3 3/16 inches long with a 1/4"-20 NC thread. This plug tap has a #7 drill size.

This SST high performance power tap is 3 3/16 inches long with a 1/4"-20 NC thread. This plug tap has a #7 drill size.

This taper hand tap is 66 millimetres long, with a M6.0 x 1.00 thread and a 6.3-millimetre shank diameter. This hand tap is made from high speed steel.

This taper hand tap is 66 millimetres long, with a M6.0 x 1.00 thread and a 6.3-millimetre shank diameter. This hand tap is made from high speed steel.

This M2 hand tap is made of high speed steel and has a 8.10mm diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 311-4241 series hand tap has a bright (uncoated) finish, and has metric measurements. It is non-coolant through, has right hand direction with a 69 mm length. Plus it has four flutes and a straight shank.

This M2 hand tap is made of high speed steel and has a 8.10mm diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 311-4241 series hand tap has a bright (uncoated) finish, and has metric measurements. It is non-coolant through, has right hand direction with a 69 mm length. Plus it has four flutes and a straight shank.

This M2 hand tap is made of high speed steel and has a 6.48mm diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 311-4201 series hand tap has a bright (uncoated) finish, and has metric measurements. It is non-coolant through, has right hand direction with a 64 mm length. Plus it has four flutes and a straight shank.

This M2 hand tap is made of high speed steel and has a 6.48mm diameter shank. It is designed for use with all materials, and meets the standards for ANSI. This 311-4201 series hand tap has a bright (uncoated) finish, and has metric measurements. It is non-coolant through, has right hand direction with a 64 mm length. Plus it has four flutes and a straight shank.

This tap wrench is made of mild steel. This tap wrench has fractional inch measurements. It has right hand direction with a 11 inch length.

This tap wrench is made of mild steel. This tap wrench has fractional inch measurements. It has right hand direction with a 11 inch length.