High-Performance Spiral-Point Taps for Nickel & Titanium

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

This straight flute tap is made of high speed steel and has a 0.367 inch diameter, 1 23/32 inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI standards. This 7301 series straight flute tap is uncoated, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3⅜ inch length. Plus it has three flutes and a straight shank.

This straight flute tap is made of high speed steel and has a 0.367 inch diameter, 1 23/32 inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI standards. This 7301 series straight flute tap is uncoated, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3⅜ inch length. Plus it has three flutes and a straight shank.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

Maintenance gun tap. High speed steel, ground thread, plug chamfer (3-5 pitches). For use by hand or for tapping under power. They are recommended for use in through holes or blind holes which allow for chip accumulation.

This pipe tap is made of powdered metal and has a 0.168 inch diameter, 1.2980 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.168 inch diameter, 1.2980 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.255 inch diameter, 1.3980 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.255 inch diameter, 1.3980 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of powdered metal and has a 0.141 inch diameter, 1.3130 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series spiral point tap has a TiCN finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1¾ inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of powdered metal and has a 0.141 inch diameter, 1.3130 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series spiral point tap has a TiCN finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1¾ inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.318 inch diameter, 1.5950 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series pipe tap has a TiCN finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2 23/32 inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.318 inch diameter, 1.5950 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series pipe tap has a TiCN finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2 23/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of powdered metal and has a 0.141 inch diameter, 1.3080 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series spiral point tap has a TiCN finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅞ inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of powdered metal and has a 0.141 inch diameter, 1.3080 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series spiral point tap has a TiCN finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅞ inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.318 inch diameter, 1.4610 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2 23/32 inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.318 inch diameter, 1.4610 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2 23/32 inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.141 inch diameter, 1.2560 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.141 inch diameter, 1.2560 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.323 inch diameter, 1.8590 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series pipe tap has a TiCN finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3 5/32 inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.323 inch diameter, 1.8590 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series pipe tap has a TiCN finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3 5/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of powdered metal and has a 0.168 inch diameter, 1.3690 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series spiral point tap has a TiCN finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of powdered metal and has a 0.168 inch diameter, 1.3690 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312TI series spiral point tap has a TiCN finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅛ inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.323 inch diameter, 1.8590 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3 5/32 inch length. Plus it has three flutes and a straight shank.

This pipe tap is made of powdered metal and has a 0.323 inch diameter, 1.8590 inch long shank. It is designed for use with nickel, titanium, and meets the standards for ANSI. This 312NI series pipe tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3 5/32 inch length. Plus it has three flutes and a straight shank.

This straight flute tap is made of high speed steel and has a 0.141 inch diameter, 1 9/32 inch long shank. It is designed for use with aluminum, brass, bronze, copper, and meets ANSI standards. This 7301 series straight flute tap is uncoated, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has two flutes and a straight shank.

This straight flute tap is made of high speed steel and has a 0.141 inch diameter, 1 9/32 inch long shank. It is designed for use with aluminum, brass, bronze, copper, and meets ANSI standards. This 7301 series straight flute tap is uncoated, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has two flutes and a straight shank.