Product ITEM is unavailable. See products from the same category below.
Engineering & Drilling Hammers
Engineering and drilling hammers drive stakes, strike chisels, place gears and pins, and perform light demolition. Also known as club hammers, they are smaller versions of sledge hammers with a lighter head and a shorter handle. The broad face on each end of the head provides a large striking area. These baby or mini sledges are swung with one hand to strike more accurately but with less force than a two-hand sledge.
Tempered spring steel bars extend the length of the handle. The bars are riveted through a steel top plate which fits into a recess formed in the hammer head. Abrasive resistant rubber is molded around the entire handle. The heads are vulcanized to the handle. 2.5 lbs, 12 inch handle length.
Tempered spring steel bars extend the length of the handle. The bars are riveted through a steel top plate which fits into a recess formed in the hammer head. Abrasive resistant rubber is molded around the entire handle. The heads are vulcanized to the handle. 2.5 lbs, 12 inch handle length.
This drilling hammer has a length of 10 inch with a two-pound head weight. The wood handle is 8 3/5 inch long. It features tempered on striking face. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This drilling hammer has a length of 10 inch with a two-pound head weight. The wood handle is 8 3/5 inch long. It features tempered on striking face. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This engineer's hammer has a length of 15 inch with a four-pound head weight. The fibreglass handle is 13⅛ inch long, is black/yellow. It meets the standards for ASME. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This engineer's hammer has a length of 15 inch with a four-pound head weight. The fibreglass handle is 13⅛ inch long, is black/yellow. It meets the standards for ASME. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This drilling hammer has a length of 10 inch with a four-pound head weight. The wood handle is 202 mm long. It features tempered on striking face. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This drilling hammer has a length of 10 inch with a four-pound head weight. The wood handle is 202 mm long. It features tempered on striking face. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This drilling hammer has a length of 11 inch with a 2½-pound head weight. The steel handle is 9 9/16 inch long. In addition, it is made of steel, plus it is non-sparking, with a ribbed grip.
This drilling hammer has a length of 11 inch with a 2½-pound head weight. The steel handle is 9 9/16 inch long. In addition, it is made of steel, plus it is non-sparking, with a ribbed grip.
Tempered spring steel bars extend the length of the handle. The bars are riveted through a steel top plate which fits into a recess formed in the hammer head. Abrasive resistant rubber is molded around the entire handle. The heads are vulcanized to the handle. 4 lbs, 12 inch handle length.
Tempered spring steel bars extend the length of the handle. The bars are riveted through a steel top plate which fits into a recess formed in the hammer head. Abrasive resistant rubber is molded around the entire handle. The heads are vulcanized to the handle. 4 lbs, 12 inch handle length.
This engineer's hammer has a length of 16 inch with a four-pound head weight. The steel handle is 16 inch long, is black. It meets the standards for ASME B107.400. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a ribbed grip.
This engineer's hammer has a length of 16 inch with a four-pound head weight. The steel handle is 16 inch long, is black. It meets the standards for ASME B107.400. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a ribbed grip.
This engineer's hammer has a length of 12 inch with a four-pound head weight. The steel handle is 12 inch long, is black. It meets the standards for ASME B107.400. In addition, it is made of copper, plus it is non-sparking, and is not tether ready with a ribbed grip.
This engineer's hammer has a length of 12 inch with a four-pound head weight. The steel handle is 12 inch long, is black. It meets the standards for ASME B107.400. In addition, it is made of copper, plus it is non-sparking, and is not tether ready with a ribbed grip.
This engineer's hammer has a length of 16 inch with a four-pound head weight. The fibreglass handle is 299 mm long and is yellow. It meets the standards for ANSI. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a plain grip.
This engineer's hammer has a length of 16 inch with a four-pound head weight. The fibreglass handle is 299 mm long and is yellow. It meets the standards for ANSI. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a plain grip.
This drilling hammer has a length of 10 inch with a two-pound head weight. The fibreglass handle is 8 5/16 inch long. In addition, it is made of steel, plus it is non-sparking, with a textured grip.
This drilling hammer has a length of 10 inch with a two-pound head weight. The fibreglass handle is 8 5/16 inch long. In addition, it is made of steel, plus it is non-sparking, with a textured grip.
This engineer's hammer has a length of 15 inch with a three-pound head weight. The fibreglass handle is 356 mm long, is black/yellow. It meets the standards for ANSI. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This engineer's hammer has a length of 15 inch with a three-pound head weight. The fibreglass handle is 356 mm long, is black/yellow. It meets the standards for ANSI. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This drilling hammer has a length of 12 inch with a 2½-pound head weight. The steel handle is 12 inch long, is black. It meets the standards for ASME B107.400. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a ribbed grip.
This drilling hammer has a length of 12 inch with a 2½-pound head weight. The steel handle is 12 inch long, is black. It meets the standards for ASME B107.400. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a ribbed grip.
This engineer's hammer has a length of 14 inch with a three-pound head weight. The fibreglass handle is 12 5/16 inch long and is yellow. It meets the standards for ASME. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This engineer's hammer has a length of 14 inch with a three-pound head weight. The fibreglass handle is 12 5/16 inch long and is yellow. It meets the standards for ASME. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This engineer's hammer has a length of 15 inch with a three-pound head weight. The wood handle is 784 mm long. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This engineer's hammer has a length of 15 inch with a three-pound head weight. The wood handle is 784 mm long. In addition, it is made of steel, plus it is non-sparking, and is not tether ready with a textured grip.
This engineer's hammer has a length of 16 inch with a three-pound head weight. The wood handle is 362 mm long. It features double faced induction hardened head. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This engineer's hammer has a length of 16 inch with a three-pound head weight. The wood handle is 362 mm long. It features double faced induction hardened head. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This engineer's hammer has a length of 16 inch with a four-pound head weight. The wood handle is 354 mm long. It features double faced induction hardened head. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
This engineer's hammer has a length of 16 inch with a four-pound head weight. The wood handle is 354 mm long. It features double faced induction hardened head. In addition, it is made of steel, plus it is non-sparking, with a plain grip.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
